Page 1 of 3 1 2 3 >
Topic Options
Rate This Topic
#44500 - 09/08/15 03:49 PM FINALLY A Soloution for Impulse Responses: False Alarm CRAP!
B32 Offline
member

Registered: 12/17/14
Posts: 35
I was rehashing all my failures with using the 11r with Reaper and came across a solotuion for using the eleven rack with ir's, without the Doubling effect.
I forget who it came from, I had it saved in notepad and must have not tried it, but it WORKS.
It was able to get it to work in Reaper. To confirm it works for real, I used Poulin Lecab because no signal will pass through if it is working right and no signal came through, until I loaded an IR. YAHOO, no latency either, I am so psyched, I just had to share.
In Reaper it shows the track names, so below translated is.
Channel 1 = Guitar In
Output 3/4 is Eleven REAMP L/R Edit: Sorry for the wrong outputs, I am little excited, lol.

Press and hold the Edit / Back button on 11R to enter user options.
Select "Rig Input"
Set the value to "Re-Amp"
In Ableton Live (or whatever), set up a track to receive on 11R channel 1 and output to 3-4.
In the DAW, dial the latency down as far possible without causing issues.


Edited by B32 (09/09/15 07:32 PM)

Top
#44502 - 09/08/15 04:10 PM Re: FINALLY A Solotion for Impulse Responses [Re: B32]
B32 Offline
member

Registered: 12/17/14
Posts: 35
Ownhammer Ir's are killer with the 11r. I do not need an axe-fx now, or an Epsi.
For those that have no idea what I'm talking about. The little trick above, is so you can use an Impulse Response loader with the 11r as your primary sound card. Today is
a good day.

Top
#44503 - 09/08/15 04:25 PM Re: FINALLY A Solotion for Impulse Responses [Re: B32]
TLTD Offline
veteran member

Registered: 02/20/11
Posts: 2734
Loc: Michigan
I'm happy with the EPSi loader, but always wished I could just go cabless into Cakewalk and load IRs in the DAW. That would still be a bit better because you can change cabinets after the fact when you end up liking something else better. Lately, I've been saving DIs, then reamping those cabless to play around with cabinet sounds and see what I like.

I'm still confused as to how this actually works, as I'd like to set it up in Cakewalk. Seems once you set input to Reamp, you'd not be able to do this in real time though?
_________________________
Soundcloud: https://goo.gl/J0VHoC
Tonefinder: http://goo.gl/WI3Ahh
YouTube: https://goo.gl/6P3Mjg

Top
#44504 - 09/08/15 05:14 PM Re: FINALLY A Solotion for Impulse Responses [Re: TLTD]
B32 Offline
member

Registered: 12/17/14
Posts: 35
No it works in real time, in Reaper anyway. That's the only way I will record. I'm not sure how to do it in Cakewalk.
Basically, you set it to Re-Amp and in the armed track, have the input set to guitar,(input 1), and the output set to 3-4(ElevenRig L/R), and it works fine. I can't believe it took so long for me to find this.


Edited by B32 (09/08/15 05:16 PM)

Top
#44508 - 09/08/15 06:13 PM Re: FINALLY A Solotion for Impulse Responses [Re: B32]
Christophersad Offline
veteran member

Registered: 06/08/13
Posts: 684
Loc: Italy
well it sounds possible,but in that way,arent you putting your cabv ir infront of the 11r in the signal chain? (dunno if im clear )
_________________________
Sometime what you Want aint what you need.

Top
#44510 - 09/08/15 06:53 PM Re: FINALLY A Solotion for Impulse Responses [Re: Christophersad]
B32 Offline
member

Registered: 12/17/14
Posts: 35
No. Your basically re routing the signal inside the 11r.
Sounds more than fine to me. To clarify, all this is doing, basically, is re-routing the signal through the re-amp input, which for some reason, allows you to monitor your signal through the DAW without adding the signal from the 11r. Hence, NO Doubling, No Pro-Tools, No Problem! Without getting to technical, it works, lol. You can't put your Daw into the signal path of your 11r, so all is the same, aside from the input re-route.


Edited by B32 (09/08/15 07:09 PM)

Top
#44513 - 09/09/15 06:22 AM Re: FINALLY A Solotion for Impulse Responses [Re: B32]
Ichil Online   content
advanced member

Registered: 01/21/15
Posts: 130
Loc: Italy
I will try this tonight: if it works I will thank you forever! laugh

Top
#44519 - 09/09/15 02:42 PM Re: FINALLY A Solotion for Impulse Responses [Re: Ichil]
Christophersad Offline
veteran member

Registered: 06/08/13
Posts: 684
Loc: Italy
where are you putting the cab loader in the daw?
_________________________
Sometime what you Want aint what you need.

Top
#44520 - 09/09/15 05:49 PM Re: FINALLY A Solotion for Impulse Responses [Re: Christophersad]
Ichil Online   content
advanced member

Registered: 01/21/15
Posts: 130
Loc: Italy
There's something that doesn't seems right: Eleven Rig L/R are "INPUTS" in Reaper and I cannot use them as outputs.
Please, can you post some screenshots of the configuration screen of the track?
Thanks a lot!

Top
#44521 - 09/09/15 06:05 PM Re: FINALLY A Solotion for Impulse Responses [Re: Ichil]
B32 Offline
member

Registered: 12/17/14
Posts: 35
Yes Chris cab loader is in the Daw. I am using Poulin lecab2 for now, but you can use any one you want. Ichil, what Sequncer are you using? I am using mine with Reaper. I will try and do some screen shots of my routing in Reaper.


Edited by B32 (09/09/15 06:06 PM)

Top
Page 1 of 3 1 2 3 >